[New Exam Dumps] Real 350-050 Exam Questions — All People Need To Learn For Not Failing Exam

Download the newest 350-050 vce dumps or 350-050 pdf dumps to prepare CCIE Wireless Written Exam, v2.0: 350-050 exam. Now, PassLeader has published the new 388q 350-050 exam dumps with PDF and VCE file download, PassLeader’s 350-050 study guide with 388q braindumps has been corrected all the questions and answers, also, all new 350-050 exam questions have been added, which will help you passing 350-050 exam easily. Download the 350-050 practice test with new questions from PassLeader quickly!

keywords: CCIE 350-050 exam,388q 350-050 exam dumps,388q 350-050 exam questions,350-050 pdf dumps,350-050 vce dumps,350-050 braindumps,350-050 practice test,350-050 study guide,CCIE Wireless Written Exam, v2.0

350-050 Exam Dumps[16]

You are conducting a site survey for a customer that is about to deploy Cisco wireless phones. Which three recommendations apply? (Choose three.)

A.    Minimum SNR should be 15 dB.
B.    The minimum recommended wireless signal strength for voice applications is -71 dBm.
C.    Minimum SNR should be 25 dB.
D.    Wireless cell overlap should be 20 percent.
E.    Minimum SNR should be 35 dB.
F.    The minimum recommended wireless signal strength for voice applications is -57 dBm.
G.    Wireless cell overlap should be 10 percent.
H.    The minimum recommended wireless signal strength for voice applications is -67 dBm.

Answer: ADF

You are implementing a WLC at a remote site and want to make sure that you are able to sync up with the Cisco WCS at the central site. Which two statements about this process are true? (Choose two.)

A.    If the WLC is behind a firewall, you must make sure that UDP ports 161 and 162 are open.
B.    The Cisco WCS server does not need direct IP connectivity to the WLC.
C.    Cisco WCS will not be able to communicate with the WLC if the WLC is behind a NAT device.
D.    If the WLC is behind a NAT device, the WLC’s dynamic AP-manager interface must be configured with the external NAT IP address.

Answer: AC

Which two options are valid mobility roles in which a controller can operate in during a client mobility session? (Choose two.)

A.    local
B.    auto anchor
C.    export anchor
D.    mobility announcer

Answer: AC

Refer to the exhibit. Which WLAN IDs will be advertised by an out-of-the-box AP that joins the WLC for the first time?

A.    5,8,12,15
B.    5,8,15
C.    8,15
D.    17,512
E.    8,15,17,512
F.    5,8,15,17,512

Answer: F

Which statement about ACLs used on a Cisco WLC is true?

A.    A WLAN ACL will override an interface access-list.
B.    An interface ACL will override a WLAN ACL.
C.    A WLAN ACL will get applied first followed by an interface ACL.
D.    An interface ACL will get applied first followed by a WLAN ACL.

Answer: A

You need to open the appropriate firewall port for RLDP. Which port must you open?

A.    UDP 6352
B.    UDP 5246
C.    TCP 37540
D.    TCP 8443
E.    TCP 16113
F.    UDP 16666

Answer: A
Rogue Location Discovery Protocol (RLDP) is an active approach, which is used when rogue AP has no authentication (Open Authentication) configured. This mode, which is disabled by default, instructs an active AP to move to the rogue channel and connect to the rogue as a client. During this time, the active AP sends de-authentication messages to all connected clients and then shuts down the radio interface. Then, it associates to the rogue AP as a client. The AP then tries to obtain an IP address from the rogue AP and forwards a User Datagram Protocol (UDP) packet (port 6352) that contains the local AP and rogue connection information to the controller through the rogue AP. If the controller receives this packet, the alarm is set to notify the network administrator that a rogue AP was discovered on the wired network with the RLDP feature.

Drag and Drop Question
Drag and drop the rogue detection “technique” on the left to the appropriate description on the right.


What are the three fundamental properties that are provided by the antenna of an AP? (Choose three.)

A.    frequency
B.    gain
C.    dB loss
D.    polarization
E.    direction
F.    modulation

Answer: BDF
An antenna gives the wireless system three fundamental properties: gain, direction and polarization. Gain is a measure of increase in power. Gain is the amount of increase in energy that an antenna adds to a radio frequency (RF) signal. Direction is the shape of the transmission pattern. As the gain of a directional antenna increases, the angle of radiation usually decreases. This provides a greater coverage distance, but with a reduced coverage angle. The coverage area or radiation pattern is measured in degrees. These angles are measured in degrees and are called beamwidths.

Refer to the exhibit. A wireless engineer at ACME Company is troubleshooting a wireless client that is unable to associate to a WLAN. What is likely the cause of the problem?
A.    The AP CAPWAP tunnel is down, and is unable to handle any new connections.
B.    The client is providing a wrong credential for dot1x authentication.
C.    The WPA PSKs do not match.
D.    The client uses WPA, but the AP is advertising only WPA2 support.
E.    A firewall is blocking the ports that are necessary for the AP to join the WLC.

Answer: B

Why would you enable the RFC 3578 option when adding a new RADIUS authentication server to a WLC?

A.    you want to run both RADIUS and TACACS
B.    to support Disconnect and Change of Authorization
C.    to encrypt communications between the WLC and the RADIUS server
D.    to support RADIUS key wrapping

Answer: B
If you are configuring a new RADIUS authentication server, choose Enabled from the Support for RFC 3576 drop-down list to enable RFC 3576, which is an extension to the RADIUS protocol that allows dynamic changes to a user session, or choose Disabled to disable this feature. The default value is Enabled. RFC 3576 includes support for disconnecting users and changing authorizations applicable to a user session and supports disconnect and change-of-authorization (CoA) messages. Disconnect messages cause a user session to be terminated immediately where CoA messages modify session authorization attributes such as data filters.

Which two statements are true with regards to RRM? (Choose two.)

A.    RRM neighbor messages are sent at the lowest mandatory speed.
B.    RRM neighbor messages are sent on channel 1.
C.    RRM neighbor messages are sent at minimum power.
D.    RRM neighbor messages are sent over the air.
E.    RRM neighbor messages are sent every 120 sec by default.

Answer: BD

Refer to the exhibit. Which two statements about this output are true? (Choose two.)

A.    Unclassified traffic belongs to the traffic class default, and packets in this class are treated as FIFO.
B.    For traffic to match class1, the traffic that is being evaluated must match one of the specified criteria.
C.    For traffic to match class1, the traffic that is being evaluated must match both of the specified criteria.
D.    Unclassified traffic will be dropped because no default class is created.

Answer: B


350-050 Exam Dumps[18]



Comments are closed.